M5Stack C6LoRA Module User Manual

M5街amp C6LORA
Model: Stamp C6LoRA
使用者手冊

描述

Stamp C6LoRa is a high-performance programmable LoRa module designed for the 830 ~ 930 MHz frequency range. The module features an ESP32-C6 SoC, an SX1262 LoRa RF transceiver, and an LNA signal amplifier chip. It comes with two onboard IPEX antenna connectors for external Wi-Fi and LoRa antennas, respectively.
At its core, the ESP32-C6 integrates a rich set of peripheral interfaces, enabling extended functionality through secondary development. It also supports 2.4GHz Wi-Fi 6, offering broader possibilities for IoT applications. Additionally, the module includes a  PI4IOE5V6408 IO expander chip, which is used for LoRa transceiver circuit control and amplifier enable signal management, delivering enhanced power efficiency and providing additional usable IO resources.
A built-in DC-DC converter supports a DC input range of 3.7 to 5V and allows for lithium battery power, making it adaptable to various hardware deployment scenarios. The module is well-suited for long-range communication applications such as smart irrigation, remote metering, and power equipment control.

規格

快速入門

3.1 準備工作

1. 訪問Arduino官方 web網站並安裝 Arduino IDE
   https://www.arduino.cc/en/Main/Software
2. 加入以下董事會經理 URL 到 File → 偏好設定 → 附加板管理器 URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. 開啟 Boards Manager，搜尋“ESP32”，然後按一下安裝。
4. After installation, select the board “ESP32C6 Dev Module.”
5. Configure the following options. USB CDC On Boot: “Enabled”

3.2 Wi-Fi測試
選擇前任amp程式“Examples” → “WiFi” → “WiFiScan”，選擇與您的裝置對應的端口，然後點擊左上角的編譯和上傳按鈕。
上傳完成後，開啟串列埠監視器 view Wi-Fi掃描資訊。

3.3 BLE掃描
選擇前任amp程式“Examp選擇“les”→“BLE”→“掃描”，選擇與您的裝置對應的端口，然後點擊左上角的編譯和上傳按鈕。
上傳完成後，開啟串列埠監視器 view BLE掃描資訊。

3.4 LoRa TX
After burning the LoRa test firmware, check the LoRa transceiver information via the ESP32-C6 USB CDC serial port.

FCC 警告

美國聯邦通訊委員會警告：
未經合規負責方明確批准的任何變更或修改都可能導致使用者操作設備的權限失效。
本設備符合 FCC 規則第 15 部分的規定。操作須符合以下兩個條件：(1) 該設備不得造成有害幹擾，且 (2) 該設備必須接受收到的任何干擾，包括可能導致意外操作的干擾。

重要提示：
筆記： 本設備經過測試，符合 FCC 規則第 15 部分對 B 類數位設備的限制。這些限制旨在提供合理的保護，防止住宅安裝中的有害幹擾。該設備會產生、使用並輻射射頻能量，如果不按照說明安裝和使用，可能會對無線電通訊造成有害幹擾。但是，不能保證在特定安裝中不會發生幹擾。如果該設備確實對無線電或電視接收造成有害幹擾（可以透過關閉和開啟設備來確定），我們鼓勵使用者嘗試透過以下一項或多項措施來糾正幹擾：

• 重新調整接收天線的方向或位置。
• 增加設備和接收器之間的距離。
• 將設備連接到與接收器所連接的電路不同的電路上的插座。
• 請諮詢經銷商或經驗豐富的廣播/電視技術人員尋求協助。

FCC 輻射暴露聲明：本設備符合針對不受控制的環境規定的 FCC 輻射暴露限制。

重要提示：
如果無法滿足這些條件（例如amp例如，某些筆記型電腦配置或與其他發射器共置），則 FCC 授權將不再有效，且 FCC ID 不能用於最終產品。在這種情況下，OEM 整合商將負責重新評估最終產品（包括發射器），並獲得單獨的 FCC 授權。

最終產品標籤
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

給最終用戶的手冊信息
OEM 整合商必須注意不要在整合此模組的最終產品的使用者手冊中向最終使用者提供有關如何安裝或拆卸此 RF 模組的資訊。
最終用戶手冊應包括本手冊中所示的所有必需的監管信息/警告。

根據 KDB 996369 D03 OEM 手冊 v01 為主機產品製造商提供整合說明

2.2 適用的 FCC 規則列表
已對 CFR 47 FCC PART 15 SUBPART C 進行了調查。 適用於模塊化變送器。

2.3 具體操作使用條件
此模組為獨立模組。如果最終產品涉及多個同時傳輸條件或獨立模組化發射器在主機中不同的運作條件，則主機製造商必須與模組製造商協商最終系統中的安裝方法。

2.4 有限模組程序
不適用

2.5 走線天線設計
不適用

2.6 射頻暴露注意事項
The device has been evaluated to meet the general RF exposure requirements. The device can be used in mobile or fixed exposure conditions with a minimum distance of 20 cm between the radiator & user’s body.

2.7 天線
This radio transmitter has been approved by the Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

2.8 標籤和合規訊息
The final end product must be labeled in a visible area with the following “Contains FCC ID: 2AN3WM5STAMPC6LORA”.

2.9 測試模式和附加測試要求的信息
The host manufacturer that installs this module with limited modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result complies with FCC part 15.247 and 15.209 requirements, then the host can be sold legally.

根據 KDB 996369 D03 為主機產品製造商提供的集成說明 OEM 手冊 v01

2.10 附加測試，第 15 部分 B 子部分免責聲明
This transmitter module is tested as a subsystem, and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rule requirements if applicable.

2.11 注意 EMI 注意事項
We recommend using “best practice” RF design engineering, testing, and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. The host manufacturer is responsible for ensuring compliance with the applicable FCC rules for the transmitters operating individually and simultaneously. This includes compliance for the summation of all emissions from all outputs occupying the same or overlapping frequency ranges, as defined by the applicable rules.

2.12 如何進行更改 – 重要提示
如果無法滿足這些條件（例如ample, certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, OEM integrator contacts Grantees to make permissive changes, or the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

只要滿足上述所有條件，就不需要進一步的發射機測試。 但是，OEM 集成商仍負責測試其最終產品是否滿足安裝此模塊所需的任何其他合規性要求。