HALO HAFH-RF Static Fixed Height Return Frame
規格
- 產品名稱： Halo Static Return Frame
- 型號變體： HAFH-RF, HAFH-SF
- 包含的組件：
- Table feet x1
- 列x1
- 螺栓： M6x12x2
- 擰： ST4x20 x13
- Side brackets x1
- 橡膠墊 x10
- Top frame-1 x1
- 螺栓： M6x10x3
- Centre bracket x1
- Center rails x2
- Top frame-2 x1
- Hand bolts M6x10 x2
- Allen Wrench(4mm) x1
- Allen Wrench(5mm) x1
- 紮帶 x2
超過view
零部件
組裝說明
步驟1
- Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of thetabletop.
步驟2
- Inset the Column to the top frame,fix column with 4pcs screws M6x12 like.
步驟3
- 將桌腳放置在立柱上並旋轉使其對齊，然後擰緊預先安裝的螺栓。
步驟4
- 將側支架放置在頂部框架上並擰緊螺栓。
步驟5
- 將返回框架連接到單一工作站並用 2 個手動螺栓固定。
- 用 2 顆螺絲 M6x10 固定中心支架。
步驟6
- 安裝桌面並用 24 個螺絲 ST4x20 固定；
- 用 2 顆 M6x10 螺絲固定中心支架
電纜橋架安裝
步驟1
- Fix the cable tray(B2-SSCT ) to the cable tray arms(HP-SSARM) with 8 pcs M6x10 screws.
步驟2
- 使用 4 顆 M8x10 螺絲將 U 型支架安裝到桌架上。
- 將走線架安裝到桌架上並用 6 顆 M6x10 螺絲固定
螢幕面板安裝（Shush30隱私螢幕）
步驟1
- Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton)
步驟2
- 使用 2 個 M30x8 螺絲將螢幕支架 (B5-SBRAC) 安裝到 Shush6 擠壓件上。
步驟3
- 使用 2 個 M10x6 螺絲將螢幕支架（B10-SBRAC）固定在桌框上。
EPS（900mm H Eco Panel）螢幕面板安裝
步驟1
- Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10Screws- Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC) holesandthe holes you have created in the Eco Panel Screen. Tighten double ended bolt with AllenkeyThe brackets direction as photos display.
步驟2
- Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
- 將 8 個 M5* 32 毫米 - 6 毫米雙頭螺栓穿過屏幕支架 (B2-SBRAC) 上的孔以及您在 Eco Panel 屏幕上創建的孔。用內六角扳手鎖緊雙頭螺栓。
常見問題解答
How many components are included in the Halo Static Return Frame?
The Halo Static Return Frame includes various components such as table feet, columns, bolts, screws, side brackets, rubber pads, top frames, hand bolts, Allen wrenches, and cable ties.
How do I install the cable tray on the desk frame?
To install the cable tray, first fix it to the cable tray arms using provided screws M6x10. Then, attach U brackets to the desk frame with screws M8x10 and mount the cable tray, securing it with screws M6x10.
What is required for installing the Eco Panel Screen?
Installing the Eco Panel Screen requires screen brackets, double-ended bolts, a drill bit (not included), and a suitable Allen key for tightening.
文件/資源
 |
HALO HAFH-RF Static Fixed Height Return Frame [pdf] 使用說明書 HAFH-RF, HAFH-RF Static Fixed Height Return Frame, Static Fixed Height Return Frame, Fixed Height Return Frame, Height Return Frame |