AKO CAMRegis Basic Owner’s Manual

AKO CAMRegis Basic

警告

• 機組應安裝在不受振動、水和腐蝕性氣體影響的地方，環境溫度不超過技術資料中規定的數值。
• For the unit to operate correctly, use only the probes supplied by AKO. For the reading to be correct, the probe should be used in a place without heat influences apart from the temperature you want to me-asure or control.
• 探頭及其電纜切勿與電源、控製或饋電電纜一起安裝在導管中。
• In the event of lengthening the NTC probe, always used shield cable and earth the mesh. In these cases, the maximum deviation will be 0.25 ºC from -40 ºC to +20 ºC (Maximum 1000 m with a minimum section of 0.5 mm2 ).
• We recommend using AKO-15586 cable. Always disconnect the power supply to do the wiring.
• The power circuit should be equipped with a switch marked as dis-connecting device of the equipment of at least 2 A, 230 V, situated near the appliance.
• The power supply cable should be H05VV-F or H05V-K type. The gauge will depend on local regulations, but should in no case be less than 1 mm2 . The electrical installation should be carried out under pipe. Using the logger not observing the manufacturer’s instructions may alter the appliance safety requirements. Only probes supplied by AKO should be used for the appliance to operate correctly.

安裝

方面

 技術規格

• Power supply……………………………………………… 90-240 V~ 50/60Hz
• Alarm relay…………………………………………………………… 8 A cos j=1
• NTC range (AKO-14931)…………………………………. -50 ºC to 99.9 ºC
• Range 4-20 mA…………. Configurable from -100 to 900 (1000 levels)
• Resolution ………………………………………………………………………..0,1
• Accuracy class (-40 ºC to 40 ºC):………………….. ±1 ºC acc/ EN 12830
• Response time:……………………………………………………. < 20 seconds
• Maximum relative time error:…………………………………………< 0.1 %
• Marked according to UNE-EN 12830……………..S,A,1,-40 ºC + 40 ºC
• ………………………………………………………… 適合儲存（S）
• ……………………………………………………..氣候環境類型（A）
• …………………………………………………………………….. 精度等級 (1)
• Maximum input power……………………………………………………8.5 VA
• Working ambient temperature…………………………………0 ºC to 40 ºC
• Storage ambient temperature……………………………… -20 ºC to 60 ºC
• Degree of protection…………………………………………………………IP40
• 電源、二次迴路和繼電器輸出之間雙重絕緣。
• Installation category……………………………………… II acc/ EN 61010-1
• Pollution degree…………………………………………… II acc/ EN 61010-1
• Maintenance of date and time without power supply……Up to 2 days
• Internal buzzer………………………………………………….. 70dB at 30 cm
• SD cards accepted……………………………………SD/SDHC (FAT / FAT32)

 接線

手術

按鍵功能

• key: A short press displays the maximum value reached in the last 24h, and the time when all the active inputs were reached. In the programming menu it allows scrolling around the different levels, or during the setting of a parameter, changing its value.
• key: A short press displays the minimum value reached in the last 24h, and the time when all the active inputs were reached. In the programming menu it allows scrolling around the different levels, or during the setting of a parameter, changing its value.
• key: A short press downloads the data of the ongoing log onto the SD card (if it has been inserted)
• key: A short press downloads ALL the logged data onto the SD card (if it has been inserted). The save without changes, return to previous level or exit programming parameter appears on the programming menu.
• SET key: A short press downloads the data of the last log onto the SD card (if it has been inserted).
• 使聲音警報靜音（根據參數 P50）。
• 編程時，確認選擇並儲存輸入的值。
•   keys : Pressing for over 10 seconds accesses the data log display menu.
• 按 選擇日誌區塊並按 SET 存取它。
• 按  選擇要顯示的日誌，1秒後將顯示每個輸入的值，指示日誌的日期和時間。
• N + O keys : Pressing for over 10 seconds accesses the alarms log display menu.
  Press N / Q to select the input to be displayed and press SET.
  Press N / Q to select the event to be displayed (no. 1 is the most recent event), after 1 second the value of each input will be displayed, indicating the date and time of the event.
• keys: Pressing them for over 10 seconds accesses the programming menu.

記錄資料的結構

• 記錄的資料以日誌區塊的形式儲存在記錄器的內部記憶體中。每個區塊儲存的時間長度以及記憶體的最大容量取決於日誌間隔（L1 參數），如表所示。
• 記錄器有一個 SD 卡插槽，可傳輸儲存的資料以在電腦上顯示或儲存為備份。這些資料以電子表格格式 (.csv) 保存，以以下方式組織：

重要的: Do not remove the SD card until the indicator turns off. The download may take several minutes depending on the data saved.

• Downloads ALL the logged data (P key)
  二 file產生的檔案名稱為下載的年、月、日，位於兩個不同的資料夾 ALL 和 ALARMS 中。第一個包含 file 在此之前設備記錄的所有數據，第二個包含 file 在此之前保存的事件（請參閱第 5.2 節）：
•  報警記錄
  This function saves an event whenever an alarm is activated or deactivated. To download the events log data, press the P key, all the data logged up to date are downloaded onto the SD card, including the events log, contained in the “ALARMS” folder.
•  初始啟動
  首次啟動時將請求日期和時間。

 編程選單（參數）
To access the parameter programming menu, press the N + Q keys at the same time. Refer to the list of available parameters in section 5 of this manual. After 20 seconds without touching any key, the unit returns to the previous level. If it is in level 3 the changes will not be saved.

參數和訊息表

德夫。列表示出廠預設參數。除非另有說明，溫度值均以°C 為單位（等效溫度以°F 為單位）。